AUTOCLAVE AUTESTER ST DRYPV III 80L

Autoclaves for sterilization “Autester ST DRY PV IIl” 80L

Microprocessor process control.
Automatic vacuum dry and purge “prevacuum”
programmable temperature from 105 °c to 134 °c (0.21 to 2 bar). Conforms to apparatus pressure regulation directives. Vertical floor standing model
capacity: 80 litres.

Ref:4002519
Category:
Share:
- Email
- Twitter
- Facebook
- Google +
- Pinterest
- Tumblr
- Linkedin
- Vkontakte

PRINCIPAL OF STEAM STERILIZATION

STERILIZATION IS THE PROCESS OF THE DESTRUCTION AND ELIMINATION OF ALL FORMS OF MICROBIAL LIFE, INCLUDING BACTERIA AND ITS SUBFORMS.

THE LABORATORY AUTOCLAVE CONSISTS OF A VESSEL IN WHICH STEAM FLOWS AT A HIGH PRESSURE WITH A STERILIZATION PURPOSE. SATURATED STEAM WILL IMMEDIATELY CONDENSE AND THUS RELEASING ITS HIGH EVAPORATION HEAT, WHICH IS IN FACT THE DESTRUCTIVE AGENT. IN ORDER THAT STERILIZATION WOULD BE EFFECTIVE, STEAM MUST BE SATURATED AND, CONSEQUENTLY, ALL THE AIR INSIDE THE VESSEL MUST BE PURGED BEFORE INITIALIZING THE PROCESS.

CONTROL PANEL

TFT touch screen with virtual pushbuttons.

1. Graphical representation of real time process

2. Start/Stop virtual pushbutton.

3. Running program.

4. Press indicator.

5. Temperature indicator.

6. Running program parameters.

BACK VIEW

1. Mains input.

2. External water supply.

3. Safety valve.

4. Vacuum vapour valve.

5. Air in filter valve.

6. Safety thermostat.

7. Safety thermostat.

8. Empty tank valve.

9. Drain tank valve.

10. RS232 connector.

11. USB connector.

CONFORMITY

EN 61010-1 SAFETY FOR EQUIPMENT FOR LABORATORY USE.
EN 61010-2-040 SAFETY FOR STERILIZER EQUIPMENT FOR LABORATORY USE.
EN 61326 ELECTROMAGNETIC COMPATIBILITY FOR EQUIPMENT FOR LABORATORY USE.

FEATURES

Stainless steel exterior and top.Stainless steel lid.Lid, six closure point system.Pulsed vacuum system and atmosphere purge.External steam generator (except 150 litres autoclave).Water reservoir for clean water for the steam generator boiler. External water connection if required.6 function modes.RS 232 for PC parameters printing (back side).Printer output.USB output for PEN-DRIVE data logging.Connection for a second temperature sensor.10 customer set programs.Lateral external probe port (except 150 litres autoclave).

SAFETY

Safety: The lid cannot be opened if the chamber is under pressure.

Safety valve: Prevents over pressure over the maximum limit.

Safety pressure switch: switches the heater power off to if over pressure.

Safety Lid: insulated lid protection.

MICROPROCESSOR FEATURES

The microprocessor controls the performing of the air extraction process, sterilizing and drying, executing the selected procedures and commands by the user, adjusting the following parameters:

• Sterilization temperature from 105°C up to 134°C.

• Sterilization time from 3’ to 59’.

• Drying time from 20’ to 60’.

• Up to 10 user-configurable programs.

• Six operating modes:

- Solid 1 - Solid 2 fractions. - Solid 3 fractions - Drying - Liquids - Liquids 2 probes

• Verification test: - Vacuum - Bowie Dick.

• Settings:

- Units – languages (Spanish, English, French).

- Printer module On/Off. - Clock: date/time.

- External water: on/off.

• Password for configuration.

• Calibration (adjustment offset)

- Temperature probe 1 - Temperature probe 2

- Water dosing. - Pressure

• Audible and visual alarm for overtemperature and insufficient temperature.

• Network failures detection and memorization

• Safety therrmostat by software

• Sterilization cycles data logging with capacity for over 500 cycles.

• Internal cleaning program

• Graphical representation of real time process

MESSAGES

1. E 2PROM
2. RTC FAULT
3. SENSOR PRECISION
4. HEATER PROBE
5. CHAMBER PROBE
6. OVER PRESSURE
7. VACUUM
8. PRESSURE
9. BOILER TEMPERATURE
10. TEMPERATURE LOW FAULT
11. INPUT ERROR
12. STERILIZATION
13. LEVEL 1
14. LEVEL 2
15. DOOR
16. PRINTER NO PAPER
17. PAPER JAM
18. ELECTRICAL FAULT